 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CMOS SyncBiFIFOTM 256 x 18 x 2 and 512 x 18 x 2 Integrated Device Technology, Inc. IDT72605 IDT72615 FEATURES: * Two independent FIFO memories for fully bidirectional data transfers * 256 x 18 x 2 organization (IDT 72605) * 512 x 18 x 2 organization (IDT 72615) * Synchronous interface for fast (20ns) read and write cycle times * Each data port has an independent clock and read/write control * Output enable is provided on each port as a three-state control of the data bus * Built-in bypass path for direct data transfer between two ports * Two fixed flags, Empty and Full, for both the A-to-B and the B-to-A FIFO * Programmable flag offset can be set to any depth in the FIFO * The synchronous BiFIFO is packaged in a 64-pin TQFP (Thin Quad Flatpack), 68-pin PGA and 68-pin PLCC * Industrial temperature range (-40oC to +85oC) is available, tested to military electrical specifications DESCRIPTION: The IDT72605 and IDT72615 are very high-speed, lowpower bidirectional First-In, First-Out (FIFO) memories, with synchronous interface for fast read and write cycle times. The SyncBiFIFOTM is a data buffer that can store or retrieve information from two sources simultaneously. Two Dual-Port FIFO memory arrays are contained in the SyncBiFIFO; one data buffer for each direction. The SyncBiFIFO has registers on all inputs and outputs. Data is only transferred into the I/O registers on clock edges, hence the interfaces are synchronous. Each Port has its own independent clock. Data transfers to the I/O registers are gated by the enable signals. The transfer direction for each port is controlled independently by a read/write signal. Individual output enable signals control whether the SyncBiFIFO is driving the data lines of a port or whether those data lines are in a high-impedance state. Bypass control allows data to be directly transferred from input to output register in either direction. The SyncBiFIFO has eight flags. The flag pins are full, empty, almost-full, and almost-empty for both FIFO memories. The offset depths of the almost-full and almost-empty flags can be programmed to any location. The SyncBiFIFO is fabricated using IDT's high-speed, submicron CMOS technology. FUNCTIONAL BLOCK DIAGRAM DA0-DA17 R/WA ENA OEA HIGH Z CONTROL CLKA INPUT REGISTER OUTPUT REGISTER MUX MEMORY ARRAY 512 x 18 256 x 18 MUX MEMORY ARRAY 512 x 18 256 x 18 RESET LOGIC CSA A2 A1 A0 P INTERFACE FLAG LOGIC RS EFBA PAEBA PAFBA FFBA 3 7 EFAB PAEAB PAFAB FFAB FLAG LOGIC POWER SUPPLY INPUT REGISTER VCC GND CLKB OUTPUT REGISTER HIGH Z CONTROL OEB R/WB ENB BYPB COMMERCIAL TEMPERATURE RANGES (c)1996 Integrated Device Technology, Inc. DB0-DB17 2704 drw 01 SyncBiFIFO is a trademark and the IDT logo is a registered trademark of Integrated Device Technology, Inc. DECEMBER 1996 DSC-2704/5 For latest information contact IDT's web site at www.idt.com or fax-on-demand at 408-492-8391. 5.18 1 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE PIN CONFIGURATIONS 11 10 09 DB1 DB3 DB2 DB0 DB4 GND DB5 DB6 DB7 DB8 DB9 VCC DB11 DB13 GND DB12 DB14 DB15 DB16 DB17 GND DB10 RS OEA 08 R/WB CLKB 07 PAEAB PAFAB EFAB FFAB G68-1 A2 A0 Pin 1 Designator OEB ENB BYPB 06 GND 05 04 03 02 01 A VCC A1 PAEBA PAFBA EFBA FFBA DA1 DA2 DA0 DA3 DA4 B GND DA5 C DA6 DA7 D DA8 DA9 E GND DA10 VCC F PGA Top View ENA CSA CLKA R/WA DA12 DA14 DA16 DA13 GND DA15 H J K L 2704 drw 02 DA17 DA11 G DA16 DA17 CLK A R/WA ENA CSA A0 A1 A2 VCC EFAB FFAB PAEAB PAFAB OEA DB17 DB16 98765432 68 67 66 65 64 63 62 61 1 10 60 11 59 12 58 57 13 56 14 55 15 54 16 53 17 J68-1 52 18 51 19 50 20 49 21 48 22 47 23 46 24 45 25 44 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 DB15 GND DB14 DB13 DB12 DB11 DB10 VCC GND DB9 DB8 DB7 DB6 DB5 GND DB4 DB3 DA15 GND DA14 DA13 DA12 DA11 DA10 VCC GND DA9 DA8 DA7 DA6 DA5 GND DA4 DA3 DA2 DA1 DA0 EFBA FFBA PAEBA PAFBA GND BYPB OEB ENB R/WB CLKB RS DB0 DB1 DB2 2704 drw 03 PLCC Top View 5.18 2 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE PIN CONFIGURATIONS EFBA FFBA PAEBA PAFBA BYBB OEB ENB CLKB R/WB GND DA1 DA0 DB0 DB1 PIN 1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 DA2 DA3 DA4 DA5 DA6 DA7 DA8 DA9 GND VCC DA10 DA11 DA12 DA13 DA14 DA15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PN64-1 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 DB3 DB4 GND DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 GND DB15 DB16 R/WA ENA CSA EFAB FFAB PAEAB PAFAB OEA A0 A1 CLKA A2 DA16 DA17 VCC RS DB17 DB2 2704 drw 04 TQFP Top View 5.18 3 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE PIN DESCRIPTION Symbol DA0-DA17 Name Data A Chip Select A Read/Write A I/O I/O I I Description Data inputs & outputs for the 18-bit Port A bus. Port A is accessed when CSA is LOW. Port A is inactive if CSA is HIGH. This pin controls the read or write direction of Port A. If R/WA is LOW, Data A input data is written into Port A. If R/WA is HIGH, Data A output data is read from Port A. In bypass mode, when R/WA is LOW, message is written into AB output register. If R/WA is HIGH, message is read from BA output register. CLKA is typically a free running clock. Data is read or written into Port A on the rising edge of CLKA. When ENA is LOW, data can be read or written to Port A. When ENA is HIGH, no data transfers occur. When R/WA is HIGH , Port A is an output bus and OEA controls the high-impedance state of DA0-DA17. If OEA is HIGH, Port A is in a high-impedance state. If OEA is LOW while CSA is LOW and R/WA is HIGH, Port A is in an active (low-impedance) state. When CSA is asserted, A0, A1, A2 and R/WA are used to select one of six internal resources. Data inputs & outputs for the 18-bit Port B bus. This pin controls the read or write direction of Port B. If R/WB is LOW, Data B input data is written into Port B. If R/WB is HIGH, Data B output data is read from Port B. In bypass mode, when R/WB is LOW, message is written into BA output register. If R/WB is HIGH, message is read from AB output register. Clock B is typically a free running clock. Data is read or written into Port B on the rising edge of CLKB. When ENB is LOW, data can be read or written to Port B. When ENB is HIGH, no data transfers occur. When R/WB is HIGH , Port B is an output bus and OEB controls the high-impedance state of DB0-DB17. If OEB is HIGH, Port B is in a high-impedance state. If OEB is LOW while R/WB is HIGH, Port B is in an active (low-impedance) state. When EFAB is LOW, the AB FIFO is empty and further data reads from Port B are inhibited. When EFAB is HIGH, the FIFO is not empty. EFAB is synchronized to CLKB. In the bypass mode, EFAB HIGH indicates that data DA0-DA17 is available for passing through. After the data DB0-DB17 has been read, EFAB goes LOW. CSA R/WA CLKA Clock A Enable A Output Enable A I I I ENA OEA A0, A1, A2 Addresses DB0-DB17 R/WB Data B Read/Write B I I/O I CLKB Clock B Enable B Output Enable B I I I ENB OEB EFAB AB Empty Flag O PAEAB AB Programmable Almost-Empty Flag AB Programmable Almost-Full Flag AB Full Flag O PAFAB When PAEAB is LOW, the AB FIFO is almost empty. An almost empty FIFO contains less than or equal to the offset programmed into PAEAB Register. When PAEAB is HIGH, the AB FIFO contains more than offset in PAEAB Register. The default offset value for PAEAB Register is 8. PAEAB is synchronized to CLKB. O FFAB When PAFAB is LOW, the AB FIFO is almost full. An almost full FIFO contains greater than the FIFO depth minus the offset programmed into PAFAB Register. When PAFAB is HIGH, the AB FIFO contains less than or equal to the depth minus the offset in PAFAB Register. The default offset value for PAFAB Register is 8. PAFAB is synchronized to CLKA. O When FFAB is LOW, the AB FIFO is full and further data writes into Port A are inhibited. When FFAB is HIGH, the FIFO is not full. FFAB is synchronized to CLKA. In bypass mode, FFAB tells Port A that a message is waiting in Port B's output register. If FFAB is LOW, a bypass message is in the register. If FFAB is HIGH, Port B has read the message and another message can be written into Port A. EFBA BA Empty Flag O PAEBA BA Programmable Almost-Empty Flag BA Programmable Almost-Full Flag O PAFBA When PAEBA is LOW, the BA FIFO is almost empty. An almost empty FIFO contains less than or equal to the offset programmed into PAEBA Register. When PAEBA is HIGH, the BA FIFO contains more than offset in PAEBA Register. The default offset value for PAEBA Register is 8. PAEBA is synchronized to CLKA. When EFBA is LOW, the BA FIFO is empty and further data reads from Port A are inhibited. When EFBA is HIGH, the FIFO is not empty. EFBA is synchronized to CLKA. In the bypass mode, EFBA HIGH indicates that data DB0-DB17 is available for passing through. After the data DA0-DA17 has been read, EFBA goes LOW on the following cycle. O When PAFBA is LOW, the BA FIFO is almost full. An almost full FIFO contains greater than the FIFO depth minus the offset programmed into PAFBA Register. When PAFBA is HIGH, the BA FIFO contains less than or equal to the depth minus the offset in PAFBA Register. The default offset value for PAFBA Register is 8. PAFBA is synchronized to CLKB. 2704 tbl 01 5.18 4 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE PIN DESCRIPTION (Continued) Symbol Name BA Full Flag I/O O Description When FFBA is LOW, the BA FIFO is full and further data writes into Port B are inhibited. When FFBA is HIGH, the FIFO is not full. FFBA is synchronized to CLKB. In bypass mode, FFBA tells Port B that a message is waiting in Port A's output register. If FFBA is LOW, a bypass message is in the register. If FFBA is HIGH, Port A has read the message and another message can be written into Port B. This flag informs Port B that the Synchronous BiFIFO is in bypass mode. When BYPB is LOW, Port A has placed the FIFO into bypass mode. If BYPB is HIGH, the Synchronous BiFIFO passes data into memory. BYPB is synchronized to CLKB. A LOW on this pin will perform a reset of all Synchronous BiFIFO functions. There are three +5V power pins for the PLCC and PGA packages and two for the TQFP. There are seven ground pins for the PLCC and PGA packages and four for the TQFP. 2704 tbl 02 FFBA BYPB RS VCC GND Port B Bypass Flag Reset Power Ground O I ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM Rating Terminal Voltage with Respect to Ground Operating Temperature Temperature Under Bias Storage Temperature DC Output Current Com'l. -0.5 to +7.0 Mil. -0.5 to +7.0 Unit V RECOMMENDED DC OPERATING CONDITIONS Symbol VCC GND VIH VIL(1) Parameter Supply Voltage Supply Voltage Input High Voltage Input Low Voltage Min. Typ. Max. Unit 4.5 0 2.0 -- 5.0 0 -- -- 5.5 0 -- 0.8 V V V V 2704 tbl 04 TA TBIAS TSTG IOUT 0 to +70 -55 to +125 -55 to +125 50 -55 to +125 -65 to +135 -65 to +150 50 C C C mA NOTE: 1. 1.5V undershoots are allowed for 10ns once per cycle. CAPACITANCE (TA = +25C, F = 1.0MHz) Symbol CIN(2) COUT(1,2) Parameter Input Capacitance Output Capacitance Conditions VIN = 0V VOUT = 0V Max. Unit 10 10 pF pF 2704 tbl 05 NOTE: 2704 tbl 03 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. NOTES: 1. With output deselected. 2. Characterized values, not currently tested. DC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 5V 10%, TA = 0C to +70C) IDT72615L IDT72605L Commercial tCLK = 20, 25, 35, 50ns Typ. -- -- -- -- -- Symbol IIL(1) IOL(2) VOH VOL ICC(3) Parameter Input Leakage Current (Any Input) Output Leakage Current Output Logic "1" Voltage IOUT = -2mA Output Logic "0" Voltage IOUT = 8mA Average VCC Power Supply Current Min. -1 -10 2.4 -- -- Max. 1 10 -- 0.4 230 Unit A A V V mA 2704 tbl 06 NOTES: 1. Measurements with 0.4V VIN VCC. 2. OEA, OEB VIH; 0.4 VOUT VCC. 3. Tested with outputs open. Testing frequency f=20MHz 5.18 5 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE AC TEST CONDITIONS In Pulse Levels Input Rise/Fall Times Input Timing Reference Levels Output Reference Levels Output Load GND to 3.0V 3ns 1.5V 1.5V See Figure 2 2704 tbl 07 +5V 1.1K D.U.T. 680 30pF* 2704 drw 05 AC ELECTRICAL CHARACTERISTICS (Commercial: VCC = 5V10%, TA = 0C to +70C) 72615L20 72605L20 Min. Max. -- 50 20 8 8 20 12 12 -- 3 6 1 6 1 3 0 3 -- -- -- -- 10 17 -- -- -- -- -- -- 27 10 -- -- -- -- 10 -- 10 10 10 12 12 -- -- or equivalent circuit Figure 2. Output Load * Includes jig and scope capacitances. Symbol fCLK tCLK tCLKH tCLKL tRS tRSS tRSR tRSF tA tCS tCH tDS tDH tOE tOLZ tOHZ tFF tEF tPAE tPAF tSKEW1 tSKEW2 Parameter Clock frequency Clock cycle time Clock HIGH time Clock LOW time Reset pulse width Reset set-up time Reset recovery time Reset to flags in intial state Data access time Control signal set-up time(1) Control signal hold time(1) Data set-up time Data hold time Output Enable LOW to output data valid(2) Output Enable LOW to data bus at Low-Z(2) Output Enable HIGH to data bus at High-Z(2) Clock to Full Flag time Clock to Empty Flag time Clock to Programmable Almost Empty Flag time Clock to Programmable Almost Full Flag time Skew between CLKA & CLKB for Empty/Full Flags(2) Skew between CLKA & CLKB for Programmable Flags(2) Commercial 72615L25 72615L35 72615L50 72605L25 72605L35 72605L50 Min. Max. Min. Max. Min. Max. Unit -- 40 -- 28 -- 20 MHz 25 10 10 25 15 15 -- 3 6 1 6 1 3 0 3 -- -- -- -- 12 19 -- -- -- -- -- -- 28 15 -- -- -- -- 13 -- 13 15 15 15 15 -- -- 35 14 14 35 21 21 -- 3 8 1 8 1 3 0 3 -- -- -- -- 17 25 -- -- -- -- -- -- 35 21 -- -- -- -- 20 -- 20 21 21 21 21 -- -- 50 20 20 50 30 30 -- 3 10 1 10 1 3 0 3 -- -- -- -- 20 34 -- -- -- -- -- -- 50 25 -- -- -- -- 28 -- 28 30 30 30 30 -- -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Timing Figures -- 4,5,6,7 4,5,6,7,12,13,14,15 4,5,6,7,12,13,14,15 3 3 3 3 5,7,8,9,10,11 4,5,6,7,8,9,10,11, 12, 13,14,15 4,5,6,7,10,11,12, 13, 14,15 4,6,8,9,10,11 4,6 5,7,8,9,10,11 5,7,8,9,10,11 5,7,10,11 4,6,10,11 5,7,8,9,10,11 12,14 13,15 4,5,6,7,8,9,10,11 4, 7,12,13,14,15 NOTES: 1. Control signals refer to CSA, R/WA, ENA, A2, A1, A0, R/WB, ENB. 2. Minimum values are guaranteed by design. 2704 tbl 08 5.18 6 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE FUNCTIONAL DESCRIPTION IDTs SyncBiFIFO is versatile for both multiprocessor and peripheral applications. Data can be stored or retrieved from two sources simultaneously. The SyncBiFIFO has registers on all inputs and outputs. Data is only transferred into the I/O registers on clock edges, hence the interfaces are synchronous. Two Dual-Port FIFO memory arrays are contained in the SyncBiFIFO; one data buffer for each direction. Each port has its own independent clock. Data transfers to the I/O registers are gated by the enable signals. The transfer direction for each port is controlled independently by a read/write signal. Individual output enable signals control whether the SyncBiFIFO is driving the data lines of a port or whether those data lines are in a highimpedance state. The processor connected to Port A of the BiFIFO can send or receive messages directly to the Port B device using the 18-bit bypass path. The SyncBiFIFO can be used in multiples of 18-bits. In a 36to 36-bit configuration, two SyncBiFIFOs operate in parallel. Both devices are programmed simultaneously, 18 data bits to each device. This configuration can be extended to wider bus widths (54- to 54-bits, 72- to 72-bits, etc.) by adding more SyncBiFIFOs to the configuration. Figure 1 shows multiple SyncBiFIFOs configured for multiprocessor communication. The microprocessor or microcontroller connected to Port A controls all operations of the SyncBiFIFO. Thus, all Port A interface pins are inputs driven by the controlling processor. Port B interfaces with a second processor. The Port B control pins are inputs driven by the second processor. RESET Reset is accomplished whenever the Reset (RS) input is taken to a LOW state with CSA, ENA and ENB HIGH. During reset, both internal read and write pointers are set to the first location. A reset is required after power up before a write operation can take place. The AB and BA FIFO Empty Flags (EFAB, EFBA) and Programmable Almost Empty Flags (PAEAB, PAEBA) will be set to LOW after tRSF. The AB and BA FIFO Full Flags (FFAB, FFBA) and Programmable Almost Full Flags (PAFAB, PAFBA) will be set to HIGH after tRSF. After the reset, the offsets of the Almost-Empty Flags and AlmostFull Flags for the AB and BA FIFO offset default to 8. PORT A INTERFACE The SyncBiFIFO is straightforward to use in micro-processor-based systems because each port has a standard microprocessor control set. Port A interfaces with microprocessor through the three address pins (A2-A0) and a Chip Select CSA pins. When CSA is asserted, A2,A1,A0 and R/WA are used to select one of six internal resources (Table 1). With A2=0 and A1=0, A0 determines whether data can be read out of output register or be written into the FIFO (A0=0), or the data can pass through the FIFO through the bypass path (A0=1). With A2=1, four programmable flags (two AB FIFO programmable flags and two BA FIFO programmable flags) can be selected: the AB FIFO Almost-Empty Flag Offset (A1=0, A0=0), AB FIFO Almost-Full Flag Offset (A1=0, A0=1), BA FIFO Almost-Empty Flag Offset (A1=1, A0=0), BA FIFO Almost-Full Flag Offset (A1=1, A0=1). Port A is disabled when CSA is deasserted and data A is in high-impedance state. IDT SYNCBIFIFO CLK MICROPROCESSOR A DATA ADDR, I/0 RAM A CONTROL LOGIC IDT SYNCBIFIFO DATA A DATA B CLK A CLK B CONTROL A CONTROL B SYSTEM CLOCK A SYSTEM CLOCK B CONTROL LOGIC DATA A DATA B CLK A CLK B CONTROL A CONTROL B CLK MICROPROCESSOR B DATA ADDR, I/0 RAM B 2704 drw 06 NOTES: 1. Upper SyncBiFIFO only is used in 18- to 18-bit configuration. 2. Control A Consists of R/WA, ENA, OEA, CSA, A2, A1, A0. Control B consists of R/WB, ENB, OEB. Figure 1. 36- to 36-bit Processor Interface Configuration. 5.18 7 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CS CSA 0 R/WA W 0 EN ENA 0 OE OEA 0 Data A I/O I Port A Operation Data A is written on CLKA . This write cycle immediately following low-impedance cycle is prohibited. Note that even though OEA = 0, a LOW logic level on R/WA, once qualified by a rising edge on CLKA, will put Data A into a high-impedance state. Data A is written on CLKA Data A is ignored Data is read(1) from RAM array to output register on CLKA , Data A is low-impedance Data is read(1) from RAM array to output register on CLKA , Data A is high-impedance Output register does not change(2), Data A is low-impedance Output register does not change(2), Data A is high-impedance Data A is ignored(3) Data A is high-impedance(3) 0 0 0 0 0 0 1 1 0 0 1 1 1 1 0 1 0 1 0 0 1 1 X X 1 X 0 1 0 1 X X I I O O O O I O 2704 tbl 09 NOTES: 1. When A2A1A0 = 000, the next BA FIFO value is read out of the output register and the read pointer advances. If A2A1A0 = 001, the bypass path is selected and bypass data from the Port B input register is read from the Port A output register. If A2A1A00 = 1XX, a flag offset register is selected and its offset is read out through Port A output register. 2. Regardless of the condition of A2A1A0, the data in the Port A output register does not change and the BA read pointer does not advance. 3. If CSA# is HIGH, then BYPB is HIGH. No bypass occur under this condition. Table 1. Port A Operation Control Signals BYPASS PATH The bypass paths provide direct communication between Port A and Port B. There are two full 18-bit bypass paths, one in each direction. During a bypass operation, data is passed directly between the input and output registers, and the FIFO memory is undisturbed. Port A initiates and terminates all bypass operations. The bypass flag, BYPB, is asserted to inform Port B that a bypass operation is beginning. The bypass flag state is controlled by the Port A controls, although the BYPB signal is synchronized to CLKB. So, BYPB is asserted on the next rising edge of CLKB when A2A1A0=001and CSA is LOW. When Port A returns to normal FIFO mode (A2A1A0=000 or CSA is HIGH), BYPB is deasserted on the next CLKB rising edge. Once the SyncBiFIFO is in bypass mode, all data transfers are controlled by the standard Port A (R/WA, CLKA, ENA, OEA) and Port B (R/WB, CLKB, ENB, OEB) interface pins. Each bypass path can be considered as a one word deep FIFO. Data is held in each input register until it is read. Since the controls of each port operate independently, Port A can be reading bypass data at the same time Port B is reading bypass data. When R/WA and ENA is LOW, data on pins DA0-DA17 is written into Port A input register. Following the rising edge of CLKA for this write, the AB Full Flag (FFAB) goes LOW. Subsequent writes into Port A are blocked by internal logic until FFAB goes HIGH again. On the next CLKB rising edge, the AB Empty Flag (EFAB) goes HIGH indicating to Port B that data is available. Once R/WB is HIGH and ENB is LOW, data is read into the Port B output register. OEB still controls whether Port B is in a high-impedance state. When OEB is LOW, the output register data appears at DB0-DB17. EFAB goes LOW following the CLKB rising edge for this read. FFAB goes HIGH on the next CLKA rising edge, letting Port A know that another word can be written through the bypass path. Bypass data transfers from Port B to Port A work in a similar manner with EFBA and FFBA indicating the Port A output register state. When the Port A address changes from bypass mode (A2A1A0=001) to FIFO mode (A2A1A0=000) on the rising edge of CLKA, the data held in the Port B output register may be overwritten. Unless Port A monitors the BYPB pin and waits for Port B to clock out the last bypass word, data from the AB FIFO will overwrite data in the Port B output register. BYPB will go HIGH on the rising edge of CLKB signifying that Port B has finished its last bypass operation. Port B must read any bypass data in the output register on this last CLKB clock or it is lost and the SyncBiFIFO returns to FIFO operations. It is especially important to monitor BYPB when CLKB is much slower than CLKA to avoid this condition. BYPB will also go HIGH after CSA is brought HIGH; in this manner the Port B bypass data may also be lost. Since the Port A processor controls CSA and the bypass mode, this scenario can be handled for BA bypass data. The Port A processor must be set up to read the last bypass word before leaving bypass mode. 5.18 8 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CS CSA 0 0 0 0 0 0 1 A2 0 0 1 1 1 1 X A1 0 0 0 0 1 1 X A0 0 1 0 1 0 1 X Read Write BA FIFO AB FIFO 18-bit Bypass Path AB FIFO Almost-Empty Flag Offset AB FIFO Almost-Full Flag Offset BA FIFO Almost-Empty Flag Offset BA FIFO Almost-Full Flag Offset Port A Disabled 2704 tbl 10 PROGRAMMABLE FLAGS The IDT SyncBiFIFO has eight flags: four flags for AB FIFO (EFAB, PAEAB, PAFAB, FFAB), and four flags for BA FIFO (EFBA, PAEBA, PAFBA, FFBA). The Empty and Full flags are fixed, while the Almost Empty and Almost Full offsets can be set to any depth through the Flag Offset Registers (see Table 3). The flags are asserted at the depths shown in the Flag Truth Table (Table 4). After reset, the programmable flag offsets are set to 8. This means the Almost Empty flags are asserted at Empty +8 words deep, and the Almost Full flags are asserted at Full -8 words deep. The PAEAB is synchronized to CLKB, while PAEAB is synchronized to CLKA; and PAEBA is synchronized to CLKA, while PAEBA is synchronized to CLKB. If the minimum time (tSKEW2) between a rising CLKB and a rising CLKA is met, the flag will change state on the current clock; otherwise, the flag may not change state until the next clock rising edge. For the specific flag timings, refer to Figures 12-15. Table 2. Accessing Port A Resources Using CS A2, A1, and A0. CSA, PORT A CONTROL SIGNALS The Port A control signals pins dictate the various operations shown in Table 2. Port A is accessed when CSA is LOW, and is inactive if CSA is HIGH. R/WA and ENA lines determine when Data A can be written or read. If R/WA and ENA are LOW, data is written into input register on the LOW-to-HIGH transition of CLKA. If R/WA is HIGH and OEA is LOW, data comes out of bus and is read from output register into three-state buffer. Refer to pin descriptions for more information. PORT B CONTROL SIGNALS The Port B control signal pins dictate the various operations shown in Table 5. Port B is independent of CSA. R/WB and ENB lines determine when Data can be written or read in Port B. If R/WB and ENB are LOW, data is written into input register, and on LOW-to-HIGH transition of CLKB data is written into PAEAB PAFAB PAEBA PAFBA Register 17 X 17 X 17 X 17 X 16 X 16 X 16 X 16 X 15 X 15 X 15 X 15 X 14 X 14 X 14 X 14 X 13 X 13 X 13 X 13 X 12 X 12 X 12 X 12 X 11 X 11 X 11 X 11 X 10 X 10 X 10 X 10 X 9 X 9 X 9 X 9 X 8 7 6 5 4 3 2 1 AB FIFO Almost-Empty Flag Offset 7 6 5 4 3 2 1 AB FIFO Almost-Full Flag Offset 0 8 0 Register 8 Register 7 6 5 4 3 2 1 BA FIFO Almost-Empty Flag Offset 7 6 5 4 3 2 1 BA FIFO Almost-Full Flag Offset 0 8 0 Register NOTE: 1. Bit 8 must be set to 0 for the IDT72605 (256 x 18) Synchronous BiFIFO. Table 3. Flag Offset Register Format. 2704 tbl 11 Number of Words in FIFO From To 0 0 1 n n+1 D-(m+1) D-m D-1 D D EF LOW HIGH HIGH HIGH HIGH PAE LOW LOW HIGH HIGH HIGH PAF HIGH HIGH HIGH LOW LOW FF HIGH HIGH HIGH HIGH LOW 2704 tbl 12 NOTES: n = Programmable Empty Offset (PAEAB Register or PAEBA Register) m = Programmable Full Offset (PAFAB Register or PAFBA Register) D = FIFO Depth (IDT72605 = 256 words, IDT72615= 512 words) Table 4. Internal Flag Truth Table. 5.18 9 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE input register and the FIFO memory. If R/WB is HIGH and OEB is LOW, data comes out of bus and is read from output register into three-state buffer. In bypass mode, if R/WB is LOW, bypass messages are transferred into BA output register. If R/WA is HIGH, bypass messages are transferred into AB output register. Refer to pin descriptions for more information. R/WB W 0 EN ENB 0 OE OEB 0 Data B I/O I Port B Operation Data B is written on CLKB . This write cycle immediately following output lowimpedance cycle is prohibited. Note that even though OEB = 0, a LOW logic level on R/WB, once qualified by a rising edge on CLKB, will put Data B into a high-impedance state. Data B is written on CLKB . Data B is ignored Data is read(1) from RAM array to output register on CLKB , Data B is LOW impedance Data is read(1) from RAM array to output register on CLKB , Data B is HIGH impedance Output register does not change(2), Data B is low-impedance Output register does not change(2), Data B is high-impedance 0 0 1 1 1 1 0 1 0 0 1 1 1 X 0 1 0 1 I I O O O O NOTES: 2704 tbl 13 1. When A2A1A0 = 000 or 1XX, the next AB FIFO value is read out of the output register and the read pointer advances. If A2A1A0 = 001, the bypass path is selected and bypass data is read from the Port B output register. 2. Regardless of the condition of A2A1A0, the data in the Port B output register does not change and the AB read pointer does not advance. Table 5. Port B Operation Control Signals. 5.18 10 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE tRS RS tRSF EFAB, PAEAB, EFBA, PAE BA EFAB, PAEAB, EFBA, PAE BA CSA, EN A, EN B tRSF tRSS tRSR Figure 3. Reset Timing 2704 drw 07 tCLK tCLKH CLKA tCLKL A0 , A1 , A2 , R/WA CSA tCS ENA tFF FFAB tDS DA0 -DA17 tSKEW1 CLKB READ DATA IN VALID NO READ OPERATION 2704 drw 08 tCH NO OPERATION tFF tDH Figure 4. Port A (AB) Write Timing 5.18 11 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE tCLK tCLKH CLKA tCLKL A0 , A1 , A2 , R/WA CSA tCS ENA tEF EFBA tA DA0 -DA17 tOLZ tOE OEA tSKEW1 CLKB NO WRITE WRITE 2704 drw 09 tCH NO OPERATION tEF VALID DATA tOHZ Figure 5. Port A (BA) Read Timing tCLK tCLKH CLKB tCLKL R/WB tCS ENB tFF FFBA tDS DB0 -DB17 tSKEW1 CLKA READ DATA IN VALID NO READ OPERATION tDH tFF tCH NO OPERATION 2704 drw 10 Figure 6. Port B (BA) Write Timing 5.18 12 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE tCLK tCLKH CLKB tCLKL R/WB tCS ENB tEF EFAB tA DB0 -DB17 tOLZ tOE OEB tSKEW1 CLKA NO WRITE OPERATION Figure 7. Port B (AB) Read Timing tCH NO OPERATION tEF VALID DATA tOHZ WRITE 2704 drw 11 5.18 13 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CLKA A0 , A1 , A2 , R/WA tCS CS A , ENA tDS DA0 -DA17 tSKEW1 CLKB D0 (First valid write) tFRL (1) D1 D2 D3 R/WB tCS ENB tEF EFAB tA DB0 -DB17 tOLZ tOE OEB 2704 drw 12 tA D0 D1 NOTE: 1. When tSKEW1 minimum specification, tFRL(Max.) = tCLK + tSKEW1 tSKEW1 < minimum specification, tFRL(Max.) = 2tCLK + tSKEW1 or tCLK + tSKEW1 The Latency Timing applies only at the Empty Boundary (EF = LOW). Figure 8. AB First Data Word Latency after Reset for Simultaneous Read and Write 5.18 14 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CLKB R/WB tCS ENB tDS DB0 -DB17 tSKEW1 CLKA D0 (First valid write) tFRL (1) D1 D2 D3 A0 , A1 , A2 , R/WA tCS CSA , EN A tEF EFBA tA DA0 -DA17 tOLZ tOE OEA 2704 drw 13 tA D0 D1 NOTE: 1. When tSKEW1 minimum specification, tFRL(Max.) = tCLK + tSKEW1 tSKEW1 < minimum specification, tFRL(Max.) = 2tCLK + tSKEW1 The Latency Timing apply only at the Empty Boundary (EF = LOW). Figure 9. BA First Data Word Latency after Reset for Simultaneous Read and Write 5.18 15 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CLKA tCS A0 , A1 , A2 , A2 , A1 , A0 , = 001 R/WA tCH CSA tCS ENA tFF FFAB tDS DA0 -DA17 tSKEW1 CLKB DATA INPUT tSKEW1 tSKEW1 BYPASS FLAG tFF tFF FIFO FLAG tCH R/WB tCS ENB tEF EFAB FIFO FLAG tEF BYPASS FLAG tEF FIFO FLAG BYPB tA DB0 -DB17 tOLZ tOE OEB 2704 drw 14 DATA OUTPUT tOHZ NOTES: 1. When CSA is brought HIGH, AB Bypass mode will switch to FIFO mode on the following CLKA LOW-to-HIGH transition. 2. After the bypass operation is completed, the BYPB goes from LOW-to-HIGH; this will reset all bypass flags. The bypass path becomes available for the next bypass operation. 3. When A-side changed from bypass mode into FIFO mode, B-side only has one cycle to read the bypass data. On the next cycle, B-side will be forced back to FIFO mode. Figure 10. AB Bypass Timing 5.18 16 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE CLKB R/WB tCS ENB tFF FFBA tFF BYPASS FLAG tFF tCH FIFO FLAG tFF BYPB tDS DB0 -DB17 tSKEW1 CLKA tCS A0 , A1 , A2 , A2 , A1 , A0 , = 001 tCS CSA tCS tSKEW1 tSKEW1 tSKEW1 DATA INPUT R/WA tCS ENA tEF EFBA FIFO FLAG BYPASS FLAG tA DA0 -DA17 tOLZ OEA 2704 drw 15 tEF tEF tEF FIFO FLAG DATA OUTPUT tOE tOHZ NOTES: 1. When CSA is brought HIGH, AB Bypass mode will switch to FIFO mode on the following CLKA going LOW-to-HIGH. 2. After the bypass operation is completed, the BYPB goes from LOW-to-HIGH; this will reset all bypass flags. The bypass path becomes available for the next bypass operation. 3. When A-side changed from bypass mode into FIFO mode, B-side only has one cycle to read the bypass data. On the next cycle, B-side will be forced back to FIFO mode. Figure 11. BA Bypass Timing 5.18 17 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE tCLKH CLKA tCLKL tCS ENA (R/W A = 0) PAEAB tCH WRITE n words in FIFO tSKEW2 (1) n+1 words in FIFO tPAE (2) tPAE CLKB tCS ENA (R/W B = 1) tCH READ 2704 drw 16 NOTES: 1. tSKEW2 the minimum time between a rising CLKA edge and a rising CLKB edge for PAEAB to change during that clock cycle. If the time between the rising edge of CLKA and the rising edge of CLKB is less than tSKEW, then PAEAB may not go HIGH until the next CLKB rising edge. 2. If a read is performed on this rising edge of the read clock, there will be Empty + (n + 1) words in the FIFO when PAE goes LOW. Figure 12. AB Programmable Almost-Empty Flag Timing tCLKH CLKA tCLKL (2) tCS ENA (R/W A = 0) PAFAB tCH WRITE Full - (m+1) words in FIFO tPAF Full - m words in FIFO tPAF CLKB tCS ENB (R/W B = 1) tCH READ 2704 drw 17 NOTES: 1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAFAB to change during that clock cycle. If the time between the rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAFAB may not go HIGH until the next CLKA rising edge. 2. If a write is performed on this rising edge of the write clock, there will be Full - (m + 1) words in the FIFO when PAF goes LOW. Figure 13. AB Programmable Almost-Full Flag Timing 5.18 18 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE tCLKH CLKB tCLKL tCS ENB (R/W A = 0) PAEBA tCH WRITE n words in FIFO tSKEW2 (1) n+1 words in FIFO tPAE (2) tPAE CLKA tCS ENA (R/W A = 1) tCH 2704 drw 18 READ NOTES: 1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAEBA to change during that clock cycle. If the time between the rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAEBA may not go HIGH until the next CLKA rising edge. 2. If a read is performed on this rising edge of the read clock, there will be Empty + (n - 1) words in the FIFO when PAE goes LOW. Figure 14. BA Programmable Almost-Empty Flag Timing tCLKH CLKB tCLKL (2) tCS ENB (R/W A = 0) PAFBA tCH WRITE Full - (m+1) words in FIFO tPAF Full - m words in FIFO tSKEW2 (1) tPAF CLKA tCS ENA (R/W A = 1) tCH READ 2704 drw 19 NOTES: 1. tSKEW2 is the minimum time between a rising CLKB edge and a rising CLKA edge for PAFBA to change during that clock cycle. If the time between the rising edge of CLKB and the rising edge of CLKA is less than tSKEW2, then PAFBA may not go HIGH until the next CLKA rising edge. 2. If a write is performed on this rising edge of the write clock, there will be Full - (m + 1) words in the FIFO when PAF goes LOW. Figure 15. BA Programmable Almost-Full Flag Timing 5.18 19 IDT72605/IDT72615 CMOS SyncBiFIFO 256 x 18 x 2 and 512 x 18 x 2 COMMERCIAL TEMPERATURE RANGE ORDERING INFORMATION IDT XXXXX X Device Type Power XX Speed X Package X Process/ Temperature Range BLANK Commercial (0C to +70C) G J PF 20 25 35 50 L 72605 72615 68-pin PGA 68-pin PLCC 64-pin TQFP Clock Cycle Time (t CLK ) in ns Low Power 256 x 18 Parallel Synchronous Bidirectional FIFO 512 x 18 Parallel Synchronous Bidirectional FIFO 2704 drw 20 5.18 20 |
Price & Availability of IDT72605L20J
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |